Smps Power Supply

Approx. Rs 1,000 / PieceGet Latest Price

Product BrochureProduct Details:

Do not use an inverter output for the Power Supply. Inverters with an output frequency of 50/60 Hz are available, but the
rise in the internal temperature of the Power Supply may result in ignition or burning.
*2. For a cold start at 25°C. Refer to Engineering Data on Catalog for details.
*3. If the output voltage adjuster (V. ADJ) is turned, the voltage will increase by more than +15% of the voltage adjustment
range. When adjusting the output voltage, confirm the actual output voltage from the Power Supply and be sure that
the load is not damaged.
*4. A characteristic when the ambient operating temperature is between –25 to 60°C.
*5. To reset the protection, turn OFF the input power for three minutes or longer and then turn it back ON.
*6. Safety Standard for a DC Input
The following safety standards apply to a DC input: UL No. 62368-1, cUR (CSA C22.2 No.62368-1), EN 62477-1, EN62368-1.
For a DC input, safety is ensured by external fuse.
Select an external fuse the meets the following conditions.
S8VK-C06024: 350 VDC min, 6A
S8VK-C12024: 350 VDC min, 8A
S8VK-C24024: 350 VDC min, 8A
S8VK-C48024: 350 VDC min, 12A
7. The value is when both rated output voltage and rated output current are satisfied.

• Universal input for worldwide applications: 100 to 240 VAC (85 to 264 VAC) 
•  DC input can be available: 90 to 350 VDC 
•  Operation temperature range: –25 to 60 °C 
•  Compact Dimension for small space 
•  Flexible installation by special mounting brackets 
• Safety standards: UL508/62368-1, CSA C22.2 No.107.1/62368-1 EN62477-1, EN62368-1 
• EMS: Conform to EN61204-3 EMI: EN55011 Class A
• Overvoltage Protection Consider the possibility of an overvoltage and design the system so that the load will not be subjected to an excessive voltage even if the feedback circuit in the Power Supply fails. If an excessive voltage that is approximately 130% of the rated voltage or more is output, the output voltage is shut OFF. Reset the input power by turning it OFF for at least three minutes and then turning it back ON again.
• Overload Protection The load and the power supply are automatically protected from overcurrent damage by this function. Overload protection is activated if the output current rises above 105% of the rated current. When the output current returns within the rated range overload protection is automatically cleared.
• Two phases application for Single phase models For All Single phase Models, S8VK-C Basically OMRON single phase power supply can be used on two phases of a 3–phase-system when some of conditions satisfy like below

The supplying voltage is below the maximum rated input. OMRON Power supply allows the input voltage equivalent or less than 240 VAC+10%. Please confirm the input voltage between two lines if the input voltage satisfies this condition before connecting. 
The external protector is needed on N input line to secure a safety. N line has no protection of a fuse internally. An appropriate fuse or circuit breaker should be connected on N input line like the following.

• Used to warn of the risk of electric shock under specific conditions.
• Used to warn of the risk of minor injury caused by high temperatures.
• Used for general mandatory action precautions for which there is no specified symbol.
• Use to indicate prohibition when there is a risk of minor injury from electrical shock or other source if the product is disassembled.  

Approx. Rs 3,000 / PieceGet Latest Price

Product BrochureProduct Details:

Wattage:
Input: 340-550
Output: 24, 48
L: 63
W: 125.2
H: 113.5
Warranty: 3

Approx. Rs 2,200 / PieceGet Latest Price

Product BrochureProduct Details:

• The value is when both rated output voltage and rated output current are satisfied. 
•  Do not use an inverter output for the product. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal temperature of the product may result in ignition or burning. If the input is connected to a UPS, do not connect a UPS with a square-wave output. Doing so will cause the internal temperature of the product to increase, possibly causing smoking or burning. 
•  The value is determined according to the Electrical Appliances and Material Safety Act. 
• Values for a cold start at 25°C. Refer to Inrush Current, Startup Time, Output Hold Time on page 9 for details. 
•  If the output voltage adjuster (V. ADJ) is turned, the voltage will increase by more than the voltage adjustment range. When adjusting the output voltage, confirm the actual output voltage from the product and be sure that the load is not damaged. 
•  The value is when both rated output voltage and rated output current are satisfied. A characteristic when the ambient operating temperature is 25°C. 
•  This is the maximum variation in the output voltage when the input voltage is gradually changed within the allowable input voltage range at the rated output voltage and rated output current. 
•  When the input voltage is 380 to 480 VAC, this is the maximum variation in the output voltage when the output current is gradually changed within the range of 0 A to the rated output current. 
•  The value is when rated output voltage, rated output current, and room temperature (25°C) are satisfied. Refer to Inrush Current, Startup Time, Output Hold Time on page 9 for details. *10. At -40 to -25°C, time will be required before the rated output voltage is output after the input voltage is input. Also, the ripple noise value may exceed the value shown in the above table. (3-phase 380 to 480 VAC input only) 
•  MTBF is calculated according to JEITA RCR-9102. 
•  Refer to Recommended Replacement Periods and Periodic Replacement for Preventive Maintenance on page 18 for details.  When using 2-phase input, conforms to EN 61000-3-2 under the following condition 960W: At the rated output voltage, and 80% or less than the rated output current
• Overvoltage will be detected to prevent the load from being subjected to excessive voltage when the feedback circuit in the Power Supply fails, etc. If an excessive voltage that is approximately 130% of the rated voltage or more is output, the output voltage is shut OFF. Reset the input power by turning it OFF for at least five minutes and then turning it back ON again.
• The load and the product are automatically protected from overcurrent damage by this function.

Approx. Rs 2,500 / PieceGet Latest Price

Product BrochureProduct Details:

Wattage: 
Input: 180-550
Output: 24, 48
L: 63
W: 125.2
H: 113.5
Warranty: 3

• Use Copper Wire Only Minimum 75 Degree C
• Max. Surrounding Air Temperature 50 Degree C
• Install In A Pollution Degree 2 Environment